Emotion Engine

The Emotion Engine consists of eight separate "units", each performing a specific task, integrated onto the same die. These units are: a CPU core, two Vector Processing Units (VPU), a 10-channel DMA unit, a memory controller, and an Image Processing Unit (IPU). There are three interfaces: an input output interface to the I/O processor, a graphics interface (GIF) to the graphics synthesizer, and a memory interface to the system memory.^[2]

The CPU core is tightly coupled to the first VPU, VPU₀. Together, they are responsible for executing game code and high-level modeling computations. The second VPU, VPU₁, is dedicated to geometry-transformations and lighting and operates independently, parallel to the CPU core, controlled by microcode. VPU₀, when not utilized, can also be used for geometry-transformations. Display lists generated by CPU/VPU0 and VPU1 are sent to the GIF, which prioritizes them before dispatching them to the Graphics Synthesizer for rendering.

The CPU core is a two-way superscalar in-order RISC processor.^[3] Based on the MIPS R5900, it implements the MIPS-III instruction set architecture (ISA) and much of MIPS-IV, in addition to a custom instruction set developed by Sony which operated on 128-bit wide groups of either 32-bit, 16-bit, or 8-bit integers in single instruction, multiple data (SIMD) fashion (e.g. four 32-bit integers could be added to four others using a single instruction). Instructions defined include: add, subtract, multiply, divide, min/max, shift, logical, leading-zero count, 128-bit load/store and 256-bit to 128-bit funnel shift in addition to some not described by Sony for competitive reasons. Contrary to some misconceptions, these SIMD capabilities did not amount to the processor being "128-bit", as neither the memory addresses nor the integers themselves were 128-bit, only the shared SIMD/integer registers. For comparison, 128-bit wide registers and SIMD instructions had been present in the 32-bit x86 architecture since 1999, with the introduction of SSE. However the internal data paths were 128-bit wide, and its processors were capable of operating on 4x32bit quantities in parallel in single registers.

It has a 6-stage integer pipeline and a 15-stage floating-point (FP) pipeline. Its assortment of registers consists of 32 128-bit VLIW SIMD registers (naming/renaming), one 64-bit accumulator and two 64-bit general data registers, 8 16-bit fix function registers, 16 8-bit controller registers. The processor also has two 64-bit integer arithmetic logic units (ALUs), a 128-bit load–store unit (LSU), a Branch Execution Unit (BXU), and a 32-bit VU1 floating-point unit (FPU) coprocessor (which acted as a sync controller for the VPU0/VPU1) containing a MIPS base processor core with 32 64-bit FP registers and 15 32-bit integer registers. The ALUs are 64-bit, with a 32-bit FPU that isn't IEEE 754 compliant. The custom instruction set 107 MMI (Multimedia Extensions) was implemented by grouping the two 64-bit integer ALUs. Both the integer and floating-point pipelines are six stages long.

To feed the execution units with instructions and data, there is a 16 KB two-way set associative instruction cache, an 8 KB^[4] two-way set associative non blocking data cache and a 16 KB scratchpad RAM. Both the instruction and data caches are virtually indexed and physically tagged while the scratchpad RAM exists in a separate memory space. A combined 48 double entry instruction and data translation lookaside buffer is provided for translating virtual addresses. Branch prediction is achieved by a 64-entry branch target address cache and a branch history table that is integrated into the instruction cache. The branch misprediction penalty is three cycles due to the short six stage pipeline.

The majority of the Emotion Engine's floating point performance is provided by two vector processing units (VPU), designated VPU0 and VPU1. These were essentially DSPs tailored for 3D math, and the forerunner to hardware vertex shader pipelines. Each VPU features 32 128-bit vector SIMD registers (holding 4D vector data), 16 16-bit fixed-point registers, four floating point multiply-accumulate (FMAC) units, a floating point divide (FDIV) unit and a local data memory. The data memory for VPU0 is 4 KB in size, while VPU1 features a 16 KB data memory.

To achieve high bandwidth, the VPU's data memory is connected directly to the GIF, and both of the data memories can be read directly by the DMA unit. A single vector instruction consists of four 32-bit single-precision floating-point values which are distributed to the four single-precision (32-bit) FMAC units for processing. This scheme is similar to the SSEx extensions by Intel.

The FMAC units take four cycles to execute one instruction, but as the units have a six-stage pipeline, they have a throughput of one instruction per cycle. The FDIV unit has a nine-stage pipeline and can execute one instruction every seven cycles.

The IPU allowed MPEG-2 compressed image decoding, allowing playback of DVDs and game FMV. It also allowed vector quantization for 2D graphics data.^[5]

The memory management unit, RDRAM controller and DMA controller handle memory access within the system.^[5]

Communications between the MIPS core, the two VPUs, GIF, memory controller and other units is handled by a 128-bit wide internal data bus running at half the clock frequency of the Emotion Engine but, to offer greater bandwidth, there is also a 128-bit dedicated path between the CPU and VPU0 and a 128-bit dedicated path between VPU1 and GIF. At 150 MHz, the internal data bus provides a maximum theoretical bandwidth of 2.4 GB/s.

Communication between the Emotion Engine and RAM occurs through two channels of DRDRAM (Direct Rambus Dynamic Random Access Memory) and the memory controller, which interfaces to the internal data bus. Each channel is 16 bits wide and operates at 400 MHz DDR (Double Data Rate). Combined, the two channels of DRDRAM have a maximum theoretical bandwidth of 25.6 Gbit/s (3.2 GB/s), about 33% more bandwidth than the internal data bus. Because of this, the memory controller buffers data sent from the DRDRAM channels so the extra bandwidth can be utilised by the CPU.

The Emotion Engine interfaces directly to the Graphics Synthesizer via the GIF with a dedicated 64-bit, 150 MHz bus that has a maximum theoretical bandwidth of 1.2 GB/s.^[6]

To provide communications between the Emotion Engine and the Input Output Processor (IOP), the input output interface interfaces a 32-bit wide, 37.5 MHz input output bus with a maximum theoretical bandwidth of 150 MB/s to the internal data bus. The interface provides enough bandwidth for the PCMCIA extension connector which was used for the network adapter with built-in P-ATA interface for faster data access and online functionality. An advantage of the high bandwidth was that it could be easily used to introduce hardware extensions like the Network Adapter with built-in IDE HDD support or other extensions to extend functionality and product lifecycle which can be seen as a competitive advantage. In newer variants (like the slim edition), the interface would however, offer vastly more bandwidth than what is required by the PlayStation's input output devices as the HDD support was removed and the PCMCIA connector design was abandoned in favor of a slimmer design.

The Emotion Engine contained 13.5 million metal–oxide–semiconductor (MOS) transistors,^[7] on an integrated circuit (IC) die measuring 240 mm².^[8] It was fabricated by Sony and Toshiba in a 0.25 μm (0.18 μm effective L_G) complementary metal–oxide–semiconductor (CMOS) process with four levels of interconnect.

The Emotion Engine was packaged in a 540-contact plastic ball grid array (PBGA).

The primary use of the Emotion Engine was to serve as the PlayStation 2's CPU.

The first PlayStation 3 revisions produced also featured an Emotion Engine on the motherboard to achieve backwards compatibility with PlayStation 2 games. However, the second revisions of the PlayStation 3 lacked a physical Emotion Engine in order to lower costs, performing all of its functions using software emulation performed by the Cell Broadband Processor, coupled with a hardware Graphics Synthesizer still present to achieve PlayStation 2 backwards compatibility. In all subsequent revisions, the Graphics Synthesizer was removed; however, a PlayStation 2 software emulator is available in later system software revisions for use with Sony's PS2 Classics titles available for purchase on the Sony Entertainment Network.

The Emotion Engine was also used in the PSX (digital video recorder) as well as the HDTV television models Sony WEGA HVX (Model Numbers KDE-xxxHVX/KDL-xxxHVX) and Sony BRAVIA KDL22PX300, all of which used PlayStation 2 hardware.

• Clock frequency: 294 MHz, 299 MHz (later versions)
• Instruction set: MIPS III, MIPS IV subset, 107 vector instructions
• 2-issue, 2 64-bit fixed point units, 1 floating point unit, 6 stage pipeline
• Instruction cache: 16 KB, 2-way set associative
• Data cache: 8 KB, 2-way set associative
• Scratchpad RAM: 16 KB
• Translation look aside buffer: 48-entry combined instruction/data
• Vector processing unit: 4 FMAC units, 1 FDIV unit
• Vector processing unit registers: 128-bit wide, 32 entries
• Image processing unit: MPEG2 macroblock layer decoder
• Direct memory access: 10 channels
• V_DD Voltage: 1.8 V
• Power consumption: 15 W at 1.8 V
• Embedded memory: 1 KB RAM, 4 KB FeRAM, 16 KB ROM^[9]

• Floating-point: 6.2 billion single-precision (32-bit) floating-point operations per second
• Perspective transformation: 66 million polygons per second
• With lighting and fog: 36 million polygons per second
• Bézier surface patches: 16 million polygons per second
• Image decompression: 150 million pixels per second

• Graphics card
• Graphics processing unit
• Computer graphics
• List of computer graphics and descriptive geometry topics
• Cell microprocessor, a design inspired by the Emotion Engine's CPU+VU0/VU1 arrangement, used in the PlayStation 3

• Hennessy, John L.; Patterson, David A. (29 May 2002). Computer Architecture: A Quantitative Approach (3 ed.). Morgan Kaufmann. ISBN 978-0-08-050252-6. Retrieved 9 April 2013.
• Diefendorff, Keith (19 April 1999). "Sony's Emotionally Charged Chip". Microprocessor Report. 13 (5). Microdesign Resources.